Pressure control proportional valves

Pressure control proportional valves

 

CRE - Direct operated pressure control proportional valve

The CRE valve is a direct operated pressure control proportional valve with cartridge execution which can be used in blocks and panels with type D-10A seat.

The valve is suitable as a pilot stage for remote control of two stage pressure control and reducing valves.

Pressure adjustment can be continuous in proportion to the current supplied to the solenoid.

The valve can be controlled directly by a current control power supply unit or by means of the relative electronic control units to exploit valve performance to the full.

The valve is available in three pressure control ranges up to 250 bar.

 
81100 | | | 3D
 

PRED3 - Pressure control proportional valve

The PRED3 valve is a direct operated pressure control proportional valve CETOP 03, with mounting interface in compliance with ISO 4401 (CETOP RP 121H) standards.

It is suitable to pilot two-stage valves, or for pressure control in hydraulic circuits.

Pressure can be modulated continuously in proportion to the current supplied to the solenoid.

The valve can be controlled directly by a current control supply unit or by means of the relative electronic control units to exploit valve performance to the full.

The valve is available in four pressure control ranges up to 350 bar.

 
81210 | | | 3D
 

PRED3G - Pressure control proportional valve - OBE

The PRED3G valve is a direct operated pressure control proportional valve with integrated electronics, CETOP 03 and mounting interface in compliance with ISO 4401 (CETOP RP 121H) standards.

It is suitable to pilot two-stage valves, for pressure control in hydraulic circuits.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

A solenoid current monitoring signal is available.

The valve is available in four pressure control ranges up to 350 bar.

Some parameters are customizable using the appropriate kit for start-up.

NOTE: to download the PDF catalogue of the old series click here 

 
81220 | | | 3D
 

PRED3J - Pressure control proportional valve for closed loop - OBE

The PRED3J valve is a direct operated pressure control proportional valve with integrated electronics, CETOP 03 and mounting interface in compliance with ISO 4401 (CETOP RP 121H) standards.

It is suitable to pilot two-stage valves, for pressure control in hydraulic circuits.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

The monitoring of the value detected by the pressure transmitter is available on pin F.

Some parameters are customizable using the appropriate kit for start-up.

The valve is available in three pressure control ranges up to 350 bar.

NOTE: to download the PDF catalogue of the old series click here 

 
81230 | | | 3D
 

PRE3 - Pilot operated pressure control proportional valve

The PRE3 is a pilot operated pressure control proportional valve, CETOP 03, with mounting interface in compliance with ISO 4401 (CETOP RP 121H) standards.

It is suitable to modulate the pressure in hydraulic circuits.

The valve can be controlled directly by a current control supply unit or by an electronic control unit to exploit valve performance to the full.

Pressure adjustment can be continuous in proportion to the current supplied to the solenoid.

Four pressure control ranges up to 350 bar are available.

 
81240 | | | 3D
 

PRE3G - Pilot operated pressure control proportional valve - OBE

The PRE3G valve is a pilot operated pressure control proportional valve with integrated electronics, CETOP 03 and mounting interface in compliance with ISO 4401 (CETOP RP 121H) standards, controlled directly by an integrated digital amplifier.

It is suitable to modulate the pressure in hydraulic circuits.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

A solenoid current monitoring signal is available.

Valves are easy to install. The driver directly manages digital settings.

NOTE: to download the PDF catalogue of the old series click here 

 
81250 | | | 3D
 

PRE* - Pilot operated pressure relief proportional valves

PRE* valves are pilot operated pressure relief proportional valves with mounting interface in compliance with ISO 6264 standards (CETOP RP 121H).

These valves are normally used to control hydraulic circuit pressure and enable the use of the full flow rate of the pump, even with settings approaching calibrated values.

The two-stage design and wide passages ensure reduced pressure drops thereby improving the system energy performance.

Pressure can be modulated continuously in proportion to the current supplied to the solenoid.

These valves can be controlled directly by a current control supply unit or by means of the relevant electronic control units to exploit valve performance to the full.

They are fitted with a manual pressure relief valve which is factory set to ≥15% of the maximum value in the pressure control range.

They are available in three sizes for flow rates up to 500 l/min and in four pressure control ranges up to 350 bar.

 
81310 | | | 3D
 

PRE*G - Pilot operated pressure relief proportional valves - OBE

The PRE*G valves are pilot operated pressure relief proportional valves with integrated electric proportional control and mounting interface in compliance with ISO 6264 (CETOP RP 121H) standards.

These valves are normally used to control hydraulic circuit pressure and enable the use of the full flow rate of the pump, even with settings approaching calibrated values.

The two-stage design and wide passages ensure reduced pressure drops thereby improving the system energy performance.

They are fitted with a manual pressure relief valve which is factory set to ≥15% of the maximum value in the pressure control range.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

A solenoid current monitoring signal is available.

The valves are easy to install. The driver directly manages digital settings.

They are available in three sizes with flow rates up to 500 l/min and in four pressure control ranges up to 350 bar.

NOTE: to download the PDF catalogue of the old series click here 

 
81320 | | | 3D
 

PRE*J - Pilot operated pressure relief proportional valves for closed loop - OBE

PRE*J valves are pilot operated pressure relief proportional valves with integrated electronics and mounting interface in compliance with ISO 6264 standards (CETOP RP 121H).

These valves are normally used to control hydraulic circuit pressure and enable the use of the full flow rate of the pump, even with settings approaching calibrated values.

The two-stage design and wide passages ensure reduced pressure drops thereby improving the system energy performance.

They are fitted with a manual pressure relief valve which is factory set to ≥15% of the maximum value in the pressure control range.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

The monitoring of the value detected by the pressure transmitter is available on pin F.

They are available in three sizes with flow rates up to 500 l/min and in four pressure control ranges up to 350 bar.

The valves are easy to install. The driver directly manages digital settings. In the event of special applications, you can customize the settings using the optional kit.

NOTE: to download the PDF catalogue of the old series click here 

 
81330 | | | 3D
 

MZE - Pilot operated pressure reducing proportional valve

MZE valves are 3-way pilot operated pressure reducing proportional valves, designed as modular versions with mounting interface in compliance with ISO 4401 (CETOP RP121H) standards.

The valves are used to reduce pressure in the secondary circuit branches thus ensuring stability of controlled pressure in the event of variations of the flow rate through the valve.

Pressure can be modulated continuously in proportion to the current supplied to the solenoid.

The valve can be controlled directly by a current control supply unit or by an electronic control unit, to exploit valve performance to the full.

The valve is available in three different pressure reduction ranges of up to 230 bar.

The valve is available only with internal drain to the T line inside the valve.

 
81500 | | | 3D
 

PZE3 - Proportional 3-way pressure reducing valve, pilot operated

— The PZE3 valve is a proportional 3-way pressure reducing valve, pilot operated with mounting surface according to ISO 4401- 03 standards.
— Its main function is to control continuously the outlet pressure on A reducing the inlet pressure P. However, the valve also prevent outlet pressure exceeding its regulated pressure value discharging in T the exceeding flow (a typical case of hydraulic counterweight or load balancing).
— The pressure is modulated continuously in proportion to the current supplied to the solenoid.
— They can be controlled directly by an amplifier or a proper electronic control unit.

 
81501 | |
 

ZDE3 - Pressure reducing proportional valve

ZDE3 valves are direct operated pressure reducing proportional valves with mounting interface in compliance with ISO 4401 (CETOP RP121H) standards.

These valves are used to reduce pressure in the secondary circuit branches thus ensuring stability of controlled pressure in the event of variations of the flow rate through the valve.

The valve can be controlled directly by a current control supply unit or by means of the relative electronic control units to exploit valve performance to the full.

 
81510 | | | 3D
 

ZDE3G - Pressure reducing proportional valve - OBE

The ZDE3G are direct operated pressure proportional valves with integrated electronics, CETOP 03 and mounting interface in compliance with ISO 4401 (CETOP RP121H) standards.

The valves are used to reduce pressure in the secondary circuit branches thus ensuring stability of controlled pressure in the event of variations of the flow rate through the valve.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

A solenoid current monitoring signal is available.

The valve is easy to install. The driver directly manages digital settings.

NOTE: to download the PDF catalogue of the old series click here 

 
81520 | | | 3D
 

DZCE* - Pressure reducing proportional valve

The DZCE* are pressure reducing proportional valves with mounting interface in compliance with ISO 4401 (CETOP RP121H) standards.

These valves, besides reducing the pressure from line P to user A, allow the flow to return from user A to discharge T when a pressure greater than the set value is generated in the downstream circuit (user A): a typical case of hydraulic counterweight or load balancing.

The pressure can be modulated continuously in proportion to the current supplied to the solenoid.

They can be controlled directly by a current control supply unit or by means of the electronic control units to exploit valve performance to the full.

They are available in CETOP P05, ISO 4401-05 (CETOP R05), ISO 4401-07 (CETOP 07) and ISO 4401-08 (CETOP 08) sizes.

Every size can be supplied with several controlled flow rates, up to 500 l/min.

 
81600 | | | 3D
 

DZCE*G - Pressure reducing proportional valve - OBE

The DZCE*G are pressure reducing proportional valves with integrated electronics and mounting interface in compliance with ISO 4401 (CETOP RP121H) standards.

These valves act as pressure reducing valves that, besides reducing the pressure from line P to user A, allow the flow to return from user A to discharge T when a pressure greater than the set value is generated in the downstream circuit (user A): a typical case of hydraulic counterweight or load balancing.

The valves are available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

A solenoid current monitoring signal is available.

The valves are easy to install. The driver directly manages digital settings. In the event of special applications, you can customize the settings using the optional kit.

NOTE: to download the PDF catalogue of the old series click here 

 
81610 | | | 3D